Research article summary (published 29 Sep 2009):

Child safety in vehicles: validation of a mathematical model and development of restraint system design guidelines for 3-year-olds through mathematical simulations.

Full Abstract

OBJECTIVE: The objectives of this study are to validate a mathematical simulation model of the Q3 ATD in an integrated forward-facing booster-type restraint in the rear seat and to evaluate restraint parameters to further develop design guidelines for this type of restraint system for forward-facing children corresponding to the size of the Q3. Only frontal impact was considered. METHODS: The software MADYMO was used to create and run the model of the restraint system and model of the child. The restraint system consisted of a seat and a safety belt. The child dummy model was the Q3. The complete model was validated to sled tests on 12 response signals: displacements of the dummy model, safety belt forces, and dummy model accelerations. The method used in the evaluation of the restraint parameters was a factorial design of experiments (DOE). The study included a total of 9 parameters: 6 related to the safety belt, such as pretensioner, load limiter, and belt anchor positions; two parameters related to the seat (stiffness and pitch angle); and one related to the foot support. The parameters were evaluated based on their effect on a number of dummy model responses. RESULTS: The validation study showed that the mathematical model predicted the ATD's kinematics and measurements. Furthermore, the parameters that had the greatest effect on the dummy model responses were the lap belt angle, the D-ring x and y positions (upper belt anchor), the retractor pretensioner, and the retractor load limiter. The lap belt angle had the greatest effects of all parameters. The resulting head x displacement was 7.8 cm shorter with a lap belt angle of 24 degrees to the horizontal, compared to a 73 degrees to the horizontal belt angle; it also resulted in a reduction of the head resultant acceleration by 9.8 g. CONCLUSIONS: In order to decrease the Q3 ATD head, chest, and pelvis accelerations and to limit the Q3 ATD head displacement, the following practices are recommended: first, position the D-ring rearward of the ATD so that the belt encloses the ATD's shoulder; second, position the lap belt anchors to make the lap belt angle 24 degrees to the horizontal, but make sure submarining is not induced; and finally, use a safety belt with pretensioner and load limiter functions. However, these recommendations need to be balanced with the recommendations for other occupant sizes, and any specific settings have to be evaluated further before introduction into vehicles.

Author information

Author/s: Johansson, Marianne (M); Pipkorn, Bengt (B); Lövsund, Per (P);

Affiliation: Saab Automobile AB, Chalmers University of Technology, and SAFER Traffic and Vehicle Safety Centre at Chalmers, Göteborg, Sweden. Marianne.Johansson(-atsign-)se.saab.com

Journal and publication information

Publication Type: Journal Article; Research Support, Non-U.S. Gov't; Validation Studies

Journal: Traffic injury prevention (Traffic Inj Prev), published in United States. (Language: eng)

Reference: 2009-Oct; vol 10 (issue 5) : pp 467-78

Dates: Created 2009/09/11; Completed 2009/09/24;

PMID: 19746311, status: MEDLINE (last retrieval date: 9/24/2009, IMS Date: )

Sourced from the National Library of Medicine. Abstract text and other information may be subject to copyright.

External Links for this article
(including full text providers, if available):

Click Electronic Full-text Provider Links to see options for finding the electronic full text links to this article. Note there may be a subscription or fee required for access to the full text. See our FAQ for information on finding FREE full text articles.

This article may also be located in paper journal collections available in many libraries. Use the Journal and Publication Information above to find the full article.

MeSH headings (categories)

This article was linked to the MESH Headings shown below.

Acceleration Accidents, Traffic Biomechanics Child, Preschool Computer Simulation Equipment Design

Equipment Safety - standards Guidelines as Topic Humans Models, Theoretical Seat Belts - statistics & numerical data Software

Related articles

These are the highest related articles currently in the database:

• Computer simulation of the accident with nine victims. 25 Jan 2006
• Development of point mass occupant injury criteria using event data recorders. 30 Dec 2005
• Crash protection of stock car racing drivers--application of biomechanical analysis of Indy car crash research. 30 Oct 2006
• The effects of wheelchair-seating stiffness and energy absorption on occupant frontal impact kinematics and submarining risk using computer simulation. 27 Feb 2003
• Misuse study of latch attachment: a series of frontal sled tests. 30 Dec 2006
• Concept of a platform-based impact isolation system for protection of wheelchair occupants from injuries in vehicle crashes. 8 May 2007
• Development of transportable wheelchair design criteria using computer crash simulation. 30 Aug 1996
• Development of a wheelchair occupant injury risk assessment method and its application in the investigation of wheelchair securement point influence on frontal crash safety. 28 Feb 2000
• A correlative investigation of simulated occupant motion and accident report in a helicopter crash. 30 Dec 1995
• Biomechanics of 4-point seat belt systems in farside impacts. 30 Oct 2006

See 100+ related articles.

Related Article Map

Legend: - FREE Full text Article. - Abstract only. - Title only. More help.

See a large map of 100+ related articles.